Browse all practice questions for the Brake System Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Brake System Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What is a common maintenance task for drum brakes?
  • How often should brake components be inspected for safety?
  • Which tool should be used to measure the thickness of a scored rotor?
  • What occurs when brake components overheat during extended use?
  • What would indicate that Technician B's assumption about the power brake booster check valve is correct?
  • What are slotted brake rotors designed to do?
  • What does the term 'drum brake' refer to?
  • What is the main consequence of a binding caliper piston in the brake system?
  • When rough machining a brake drum, what is the acceptable depth of cut and spindle feed rate?
  • What commonly causes the brake warning light on a vehicle dashboard to activate?
  • When a brake pedal is hard to push a few minutes after the engine is turned off, what does Technician A say regarding this condition?
  • What is used to bottom the caliper piston during brake pad replacement?
  • What does a brake booster do?
  • If the left front rotor of a vehicle with composite rotors is scored but above 'discard' thickness and the right front rotor has minor heat checks, what should you do if cast rotors are the only replacements available?
  • What can cause a vehicle to pull to one side when brakes are applied?
  • If a vehicle pulls to the right when the brakes are applied, what could be the cause according to Technician A?
  • Which is NOT a common cause of brake fade?
  • Which issue would NOT cause the brake warning light to illuminate when the brake pedal is depressed?
  • What tool can be used to apply a non-directional finish to a disc brake rotor?
  • What is the function of the bar removed from the brake assembly when the parking brakes are applied?
  • What does ABS stand for in the context of a brake system?
  • If a driver experiences ABS engagement every time they apply the brakes on uneven surfaces, what does this indicate?
  • If a driver has issues with the ABS system on cobblestone roads, what action should be taken?
  • What is a common symptom of warped brake rotors?
  • What should be done if corrosion and light scoring are found in a wheel cylinder bore?
  • If a technician cannot get any fluid to come out of the disc brake caliper bleeder screws when using a pressure bleeder, what is the MOST LIKELY cause?
  • When experiencing brake issues, which should NOT be a concern for technicians?
  • In a brake system test, what should exist on the booster side?
  • In disc brakes, what is the function of the caliper?
  • What does an erratic waveform from a wheel speed sensor typically indicate?
  • How are DTCs commonly accessed in an ABS system?
  • In an adjustment procedure, Technician A claims that new brake shoes are being adjusted after installation. Technician B asserts that the procedure is for brake drum removal. Who is right?
  • Which of the following components is associated with reducing pedal pulsation?
  • What is the recommended interval for changing brake pads?
  • In a duo-servo type drum brake design, which shoe is typically longer and thicker?
  • What could indicate that the master cylinder is failing?
  • What could suggest the need for a brake system overhaul?
  • When applying moderate pressure to the brake pedal of a HydroBoost system after depleting the fluid reserve, what should happen if the system operates properly?
  • Which situation indicates the need for bleeding the brakes?
  • Which of the following can cause issues in the Hydro-Boost braking system?
  • A customer has replaced their front disc brake pads and now the ABS warning light is on. What could be a potential cause for this issue?
  • When should brake fluid be changed in a vehicle?
  • What does a 4-channel ABS system allow during an ABS stop?
  • What is an essential condition for the correct operation of ABS systems during braking?
  • What is the impact of moisture in brake fluid?
  • Which condition is critical for a caliper with a stroking seal during rebuilding?
  • Which technician is correct in stating that an integral ABS system is a high-pressure system?
  • What generally happens when the proportioning valve in a braking system malfunctions?
  • If purple fluid is found in the master cylinder reservoir, what does this indicate regarding the brake fluid?
  • What component in the Hydro-Boost system provides power assist if there is a loss of hydraulic pressure to the system?
  • What is NOT a cause for parking brake failure on an incline?
  • Which disc brake rotor measurement cannot be performed with a micrometer?
  • What might a grinding noise during braking suggest?
  • What is the role of the master cylinder in a hydraulic brake system?
  • What is the primary function of a brake system in a vehicle?
  • Which adjustment may be necessary if caliper levers are out of alignment?
  • Describe the purpose of the parking brake.
  • What type of fluid is commonly used in hydraulic brake systems?
  • What level of tire slip is maintained by an anti-lock brake system?
  • What does a malfunctioning proportioning valve typically result in?
  • How can a driver ensure maximum life and performance of brake pads?
  • When cleaning a disc brake rotor after machining, what is the recommended cleaning solution?
  • When evaluating intermittent ABS activation without DTCs, which of the following should be checked first?
  • What may cause drum brake drag?
  • Which is NOT true about leading-trailing type drum brakes?
  • Which technician suggests that a leaking booster check valve is the cause for a hard brake pedal when the engine is off?
  • What is the most common cause for premature front brake pad wear?
  • What precaution should be taken when replacing brake pads?
  • What does Technician A claim the tool is used for that adjusts brake shoes?
  • What is the likely effect if measurements taken from the brake system vary from the manufacturer's specifications?
  • The diameter of drums mounted on the same axle should measure within how many thousands of an inch of each other?
  • What is the most likely cause if the rear wheels lock up during a quick stop?
  • True or False: Drum brakes are more efficient than disc brakes in dissipating heat.
  • What is a principal benefit of slotted brake rotors?
  • Which of the following statements about wheel bearings is true?
  • Why must new disc brake pads undergo a burnishing process?
  • A customer complains that the parking brake will not keep his car stationary. Who is right regarding the technician's diagnosis?
  • What is the reason for a need to burnish new pads during the testing process?
  • Which brake component's failure can directly trigger the brake light?
  • What component could lead to a spongy brake pedal feel if it is leaking?
  • Who is correct about ABS wheel speed sensor gap adjustments?
  • Name one environmental factor that can affect brake performance.
  • What component is primarily responsible for creating the hydraulic pressure in a hydraulic brake system?
  • Which factor can lead to brake fade?
  • What could cause the parking brake pedal to remain depressed in drive?
  • Who is correct regarding the caliper seal installed in the caliper bore?
  • How can the front brakes on a vehicle with integral ABS be bled?
  • What purpose does the master cylinder residual check valve serve on vehicles equipped with drum brakes?
  • What does a geyser from the master cylinder reservoir indicate?
  • Which statement about traction control systems is correct?
  • What should be done if excessive wear is detected on brake shoes?
  • What indicates that brake pads need replacement?
  • What tool is recommended to determine if an intermittent ABS problem is related to an erratic wheel speed sensor signal?
  • Why is it essential to bed new brake pads?
  • According to Technician A, how can tapered roller bearings be adjusted?
  • What should be checked if the brake pedal sinks to the floor when pressed?
  • How can excessive slack in parking brake cables typically be adjusted?
  • What is a reason for brake rotor refinishing?
  • In the proper procedure for replacing disc brake pads, what is done to accommodate new pads?
  • What is one potential cause of a spongy brake pedal?
  • What can lead to diminished stopping power in a braking system?
  • What brake fluid typically has a higher boiling point compared to regular brake fluid?
  • What could cause the brake warning light to stay illuminated?
  • Technician A says surge bleeding is used alongside manual or pressure bleeding. Technician B claims it removes trapped air from the brake hydraulic system. Who is correct?
  • How does ABS prevent wheel lock-up during braking?
  • Describe the effect of tire condition on brake performance.
  • What is brake fade and what causes it?
  • What is a potential cause for the brakes failing to release properly?
  • What is the purpose of brake rotors?
  • What is the purpose of brake cooling fins on rotors?
  • What type of noises may indicate that brake pads are worn out?
  • What does the number on a brake drum indicate?
  • What is the most cost-efficient method to correct excessive lateral runout on a disc brake rotor?
  • In a brake system, what does 'boost' refer to?
  • Which of the following factors would not typically cause a parking brake pedal to stay engaged?
  • What is the main difference between open and closed systems in braking?
  • How do worn rotor surfaces affect braking performance?
  • Why is it important for brake rotors to be free of contaminants?
  • What can the set-up used in the brake system check for?
  • Which of the following could NOT cause a pulsation in the brake pedal?
  • What condition might cause the brake pedal to move down slightly when the engine is started in a vehicle with vacuum-assisted power brakes?
  • Which component is NOT typically replaced when making brake measurements?
  • Which technician is correct regarding the gravity bleeding of brake systems?
  • What is the function of brake calipers?
  • In brake adjustments, Technician A states that rear brake shoes should be adjusted before adjusting the parking brake. Technician B believes the parking brake lever must be disengaged first. Who is correct?
  • What is the function of a proportioning valve in a brake system?
  • What should be the correct repair procedure for a leaking hydraulic brake line?
  • Which type of ABS system is characterized as an add-on system?
  • Which component can fail along with traction control systems?
  • What does the term ‘brake balance’ refer to?
  • Which of the following is a disadvantage of drum brakes?
  • What type of disc brake caliper design allows brake pads to be removed without removing the caliper?
  • What is the function of brake lines in a hydraulic brake system?
  • What type of fluid would indicate contamination if found in the master cylinder reservoir?
  • What could cause the front brakes on a car with disc/drum brakes to grab quickly when light pedal pressure is applied?
  • Can using the wrong brake fluid type affect braking performance?
  • Which component applies pressure to the brake pads in a disc brake system?
  • Which technician is correct regarding the effects of aging brake fluid?
  • What happens when a vehicle’s brake pads are worn down to the backing plate?
  • Which of the following can reduce the lifespan of brake pads?
  • What percentage can the boiling point of DOT 3 brake fluid be reduced by due to 3% moisture absorption?
  • What does it indicate if a brake pedal feels hard and does not move?
  • What does brake pedal travel refer to?
  • Which type of brake system typically provides better stopping power under wet conditions?
  • What type of brake system uses hydraulic fluid to apply pressure to brake components?
  • What should be checked to determine the serviceability of a brake drum?
  • What does a pulsating brake pedal often indicate?
  • What is a potential indicator of improper brake system operation?
  • During a brake inspection, what does a damp area beneath the master cylinder indicate according to Technician A?
  • While replacing a front brake hose, Technician A suggests connecting the end to the caliper first. Technician B states that a new copper sealing washer must be used. Who is correct?
  • Which of the following brake symptoms can be caused by wheel bearing problems?
  • What does a brake pad wear indicator signal?
  • What aspect of brake maintenance is crucial for maintaining performance?
  • How can a driver check the brake fluid level?
  • Which of the following components is NOT part of a disc brake system?
  • What is a common symptom of brake fade?
  • What does regular brake inspection prevent?
  • What type of brake system is typically used in heavy-duty trucks?
  • What master cylinder condition can cause brakes to drag or fail to release?
  • What is a likely cause for a brake pedal that moves slowly to the floor while maintaining pressure at a stoplight in a vehicle with power disc/drum brakes?
  • Which of the following could cause disc brake squeal?
  • What aspect of brake performance can be affected by low brake fluid levels?
  • What does Technician B suggest if dampness is found below the master cylinder of a vacuum brake booster?
  • What is a symptom of low brake fluid level?
  • If a vehicle exhibits intermittent ABS activation without DTCs found, what could be a likely cause?
  • When replacing an integral hub/bearing assembly on a front wheel drive vehicle, which component does NOT need to be removed?
  • When working on a vehicle with an integrating ABS, which tool is typically recommended for diagnostic purposes?
  • What maintenance practice is crucial for ensuring the longevity of brake components?
  • Who is correct about accessing DTCs in an ABS system?
  • What is the primary function of a brake warning light?
  • What is the most appropriate procedure for repairing a wheel cylinder?
  • What is the boiling point comparison between DOT 5 and DOT 4 brake fluid according to Technician A?
  • Which method is a procedure for removing air from a hydraulic braking system?
  • How does brake fluid temperature affect braking efficiency?
  • Which component helps to increase the friction during braking?
  • Which measurement technique is inappropriate for adjusting tapered roller bearings?
  • Where should a technician sample brake fluid to accurately check its condition?
  • When machining a rotor, what must be true about material removal?
  • What is the purpose of brake fluid reservoirs?
  • What is the term for the unevenness felt through the brake pedal during operation?
  • Which component in the hydraulic system activates the brake light when there is a leak?
  • What is a common consequence of brake fluid corroding the ABS control valves?
  • What can cause a brake system to become less effective over time?
  • In a vehicle with single piston floating caliper front disc brakes, what is a likely reason for uneven brake pad wear?
  • What is the MOST LIKELY cause of a pulsation felt through the pedal after a complete front brake service?
  • What does Technician B claim is necessary when testing a proportioning valve in vehicles with diagonally-split hydraulic systems?
  • What is one potential cause for grabbing brakes?
  • What are ceramic brake pads known for?
  • In the context of ABS, what does the system primarily aim to prevent during sudden braking?
  • What can excessive brake dust indicate?
  • Which condition would NOT cause a hard brake pedal in a vehicle with power brakes?
  • What is the effect of high water levels on brake performance?
  • What is true regarding phenolic caliper pistons?
  • What problem may arise from using a residual check valve in a disc brake master cylinder?
  • Who is correct regarding the importance of caliper condition during rebuilding?
  • What is an indicator of proper brake adjustment for drum brakes?
  • Regarding brake fittings, Technician A claims all brake systems share the same type of fitting. Technician B disagrees, stating the flare was formed with an inverted flaring tool. Who is correct?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy